POST
|
Wow thank you very much! It worked perfectly Grazie!
... View more
09-22-2016
04:15 AM
|
0
|
0
|
540
|
POST
|
Hi there, I have a layer showing the position of some vacant lands in Naples in form of polygons. I need now to assign to each parcel a random name (even just a,b,c,aa,ba,ca,etc.). I have almost 30000 objects here so I really would like to know if there is an operation that would save me from naming the parcel.. one by one manually! I'm doing this because I want to summarize my results, I tried to do that with the default ObjectID but for some reasons the button Summarize can't be executed on that. Please, any suggestion at all? Thanks, Martina
... View more
09-21-2016
11:57 AM
|
0
|
2
|
1324
|
POST
|
Hi Dan, Thanks a lot for your answer. So my suitability model counts so far 6 different variables: slope, population density, distance to public transports, to communities venue, to schools and universities as well. They were previously vector data that I transformed into raster when I calculated the distance (except for the slope which was already a raster obtained from the elevation naturally). Afterward, I run the reclassify tool in order to find those vacant lands close to areas with high density of population, little slope and close to all the amenities I listed above. Finally, I used the weighted overlay. I already got a shapefile containing the polygons of the current vacant lands but I sincerely don't know how to insert that variable in the suitability model without affect the results. I plan to overcome that by doing a 'selection by location' on the areas with the highest suitability range obtained from the model I described you above. I got the software license thanks to the university so I can access to all the range of products inside ArcGis but I don't know how to use other software apart from Envi. I'm not prepared at all on statistics but, if I'll just need the understanding of unadvanced topics, I can always have a look of the literature I guess. Following the definition that you also wrote, it would be too simplistic if I just change the % of influence when I'm doing the weighted overlay? I read somewhere that when performing the SA we should pick the variables which in our opinion have the highest importance. In this case for me were the proximity to high-density population areas to schools and transports. Although perhaps I would need to figure out from how to calculate the statistics in order to show what I did... I'm a bit lost..
... View more
08-28-2016
07:50 AM
|
0
|
1
|
1634
|
POST
|
Hi there, I was wondering how to do the sensitivity analysis on ArcGis? I see there's a guide for the version 9.2 ( ArcGIS Desktop Help 9.2 - Performing sensitivity analysis ) but I don't understand much the steps because the explanation gives for granted that I made a ModelBuilder which is not my case. I made a suitability model for urban abandoned spaces that can be reused for projects of environmental remediation and now I want to check its reliability. As I understood, the best way to do this is the sensitivity analysis but I didn't find any document or web page (apart from the one above) that show how to perform that with ArcGis specifically. So my questions is: can someone kindly explain to a beginner how to perform the sensitivity analysis, please? Otherwise, if any of you know any other approach to check the validity of a suitability model I'd really appreciate any suggestion or tip you may have Thank you Martina
... View more
08-27-2016
09:00 AM
|
0
|
3
|
3705
|
POST
|
Hi Dan, Thank you for your reply. It was previously a vector layer representing the land use of Naples in form of polygons. I did a bit of editing on it, I selected only some areas and eventually I added few more polygons with the Editor tool. After that I converted the vector into a raster layer with the Conversion tool "polygon to raster". The size extent is top: 4542695,9645 right: 951322,4801 bottom: 4528535,9645 left: 932662,4801 Is there any other information I should provide you that may help to understand where is the issue? And yes, I tried to run Reclassify of this layer on a different map but actually I got the same result. I also tried to repeat all the passages I said above from the original vector layer once again but.. nothing
... View more
08-12-2016
11:50 PM
|
0
|
1
|
263
|
POST
|
Hi there, I'm experiencing a problem with the Reclassify function on Arcgis 10.1.2. Each time I try to save my work right after I create a new raster with this function, ArcGis collapses. All I got is a message that Arcmap encountered an unexpected error and Windows closed straight away the program. I disabled the Background process but nothing changes. I noticed though that this happens only with a particular layer but I haven't experienced similar problems when I run the reclassify with previous rasters. Can anyone help me please? Thanks, Martina
... View more
08-12-2016
02:33 AM
|
0
|
3
|
1222
|
Online Status |
Offline
|
Date Last Visited |
11-11-2020
02:24 AM
|