POST
|
Dan, I'm not familiar with 3D or numpy, so I don't know if they are capable of the same raster calculation. Something to look into, thanks!
... View more
10-22-2016
09:13 AM
|
0
|
1
|
1104
|
POST
|
I would like to create a tool to use in Model Builder with other tools to automate a series of processes that involves creating a raster in ArcGIS then running a script in R and adding the results back into ArcGIS. See my original post for the exact function I am using in R.
... View more
10-20-2016
01:56 PM
|
0
|
3
|
1104
|
POST
|
Thanks for the reply, Steve! Looking forward to when raster data is supported to be able to automate some processing.
... View more
10-20-2016
11:35 AM
|
0
|
5
|
1104
|
POST
|
I have an R script that uses the spatialEco package to create percent volume rasters. It works well as a stand-alone script but I would like to create a script tool in ArcGIS to use in ModelBuilder. The error I am getting seems related to the fact that the 'raster.vol' function needs to operate on a raster layer object but when I use the 'arc.open' function in my script, my raster opens as a :RasterDataset and arcgisbinding doesn't seem to have an inherited method to allow me to use the 'raster' function to convert the object to a raster layer. Any suggestions?
... View more
09-29-2016
10:36 AM
|
0
|
7
|
2059
|
POST
|
Thanks, Dan. Eric Krause actually had the reasoning I was looking for. I didn't realize the GA layer wasn't showing the full extent of predicted values that are seen in the raster created from it.
... View more
09-08-2016
05:09 PM
|
1
|
1
|
1236
|
POST
|
Thanks, Steve. I have read this before, it wasn't clear to me why the GA layer didn't show negative values. Eric Krause's answer helped.
... View more
09-08-2016
05:08 PM
|
0
|
0
|
1236
|
POST
|
I understood that RBF could result in values above or below, what I didn't realize is that the values shown in the GA layer weren't the full extent. Thank you. Using a different subset of my data, I didn't see the negative values when making the raster from the GA layer and so thought this was strange. But looking at my point spread between the two subsets, I see that there is a greater 'no data' area in the second subset and that must be influencing the negative raster values.
... View more
09-08-2016
05:06 PM
|
0
|
0
|
1236
|
POST
|
I have used the Geostatistical Analyst Wizard to interpolate point data using the radial basis function. The GA layer created has a minimum value of "0" and a maximum value of "114" which correlates to the point data values used. However, when I use the tool "GA Layer to Grid", I am getting a minimum value of "-4.04". I understand the mins and maxes for the raster aren't going to match because the values are averaged within the cell created, but how can a negative value be returned when none exist in the original point data or the GA layer?
... View more
09-08-2016
03:27 PM
|
0
|
8
|
2612
|
POST
|
It does work manually in ArcMap using the Make XY Event Layer tool. I have tried deleting the tool in ModelBuilder and adding it back in with no success. I'm truly stumped!
... View more
06-24-2016
03:32 PM
|
0
|
0
|
1182
|
POST
|
Other than the projection differences, your Make XY Event Layer code is the same as mine. Thanks, though.
... View more
06-22-2016
02:55 PM
|
0
|
0
|
1182
|
POST
|
ERROR 000212: Cannot create XY event source Failed to execute (MakeXYEventLayer)
... View more
06-22-2016
02:54 PM
|
0
|
0
|
1182
|
POST
|
Had a model built that worked about a month ago and today I can't figure out why it is getting stuck at the Make XY Layer step. Here is the Python code from the model: arcpy.MakeXYEventLayer_management(CopiedTbl_View, "Lon", "Lat", XYLayer, "GEOGCS['GCS_WGS_1984',DATUM['D_WGS_1984',SPHEROID['WGS_1984',6378137.0,298.257223563]],PRIMEM['Greenwich',0.0],UNIT['Degree',0.0174532925199433]];-400 -400 1000000000;-100000 10000;-100000 10000;8.98315284119522E-09;0.001;0.001;IsHighPrecision", "") I made sure that the table being imported from an Access database in previous steps has the Lat/Lon field in numeric format and still it doesn't work. I have attached a pic of the whole model for reference.
... View more
06-21-2016
02:57 PM
|
2
|
8
|
5480
|
Title | Kudos | Posted |
---|---|---|
1 | 09-08-2016 05:09 PM | |
2 | 06-21-2016 02:57 PM |
Online Status |
Offline
|
Date Last Visited |
11-11-2020
02:24 AM
|